最近做项目用需要用到两个串口，分别是串口1和串口2，
串口1接调试，传感器等，串口2对接蓝牙与APP通讯
芯片型号：STC8H3K64S4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
|
#include "stc8h.h"
#define S2RI 0x01 //串口2接收中断请求标志位
#define S2TI 0x02 //串口2发送中断请求标志位
char flag = 0;
unsigned char UART2_ReceiveBuffer[10]={0};
void Uart2_Init(void) //9600bps@22.1184MHz
{
S2CON = 0x50; //8位数据,可变波特率
AUXR |= 0x04; //定时器2时钟为Fosc,即1T
T2L = 0xC0; //设定定时初值
T2H = 0xFD; //设定定时初值
AUXR |= 0x10; //启动定时器2
EA = 1;
IE2 = 0X01; //打开接收中断
}
void UART2_SendByte(unsigned char mydata)
{
IE2 = 0X00;
S2CON&=~S2TI; //TI = 1
S2BUF=mydata;
while((S2CON&S2TI)==0);
S2CON&=~S2TI; //TI = 1//清除发送标志位
IE2 = 0X01;
}
void Uart2_SendString(unsigned char *p) //串口2发送一个字符串
{
while(*p!='\0')
{
UART2_SendByte(*p);
p++;
}
}
void Uart2_InterruptService(void) interrupt 8
{
unsigned char temp;
static char i = 0;
if(S2CON&S2RI) //RI == 0
{
flag = 1;
S2CON&=~S2RI; //RI = 1
temp = S2BUF;
UART2_ReceiveBuffer[i] = temp;
if(i == 10)
{
i=0;
}else{
i++;
}
}
}
void main()
{
Uart2_Init();
Uart2_SendString("start\n");
while(1)
{
if(flag == 1)
{
IE2 &= ~S2RI;
S2BUF = temp;
while(!(S2CON&S2TI));
S2CON&=~S2TI;
IE2 |= S2RI;
flag = 0;
}
}
}
|
注意：
在用STC_60s2单片机进行双串口同时收发时，要注意一些容易配置错误的地方。
AUXR寄存器有很多功能。
在对其中的位置位和复位时，很可能在不同的地方多次进行，应该使用 AUXR |= bitx 和 AUXR &=~bitx 语句进行对某一位的置位和复位。
这样就不会影响其他功能位了。
附上程序：
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
#include <STC12C5A60S2.h>
//sfr AUXR = 0x8E;
#define uchar unsigned char//
#define uint unsigned int //
#define BUADRATE 38400
#define FOSC 24000000
#define S2RI 0x01
#define S2TI 0x02
sbit LED1 = P2^7;
uchar ReceBuf[200]= {0};
bit finishflag = 0;
uchar revcnt = 0;
uchar startflag = 0;
void InitUART1(void) //baudrate 115200
{
TMOD = 0x20;
SCON = 0x50;
TH1 = 0xf3; //115384
TL1 = TH1;
PCON = 0x80; //SMOD = 1;
ES = 1;
TR1 = 1;
}
void InitUART2() //baudrate 38400
{
S2CON = 0x50; //8-Bit 串口模式 允许接收
BRT = 236; //[24000000/(256-236)]/32 = 37500 error2.34%
AUXR |= 0x14; //BRTR=1使能BRT BRTx12=1 不分频 （AUXR 第二次出现，不能用‘=’应该用“|=”）
IE2 = 0x01; //enable UART2 interrupt
AUXR1 = 0; //UART2 TXD->P1.3 RXD->P1.2
}
void SendOneByte(unsigned char c)
{
SBUF = c;
while(!TI);
TI = 0;
}
void U1SendString(uchar *dat)
{
while(*(dat)!='\0')
{
SendOneByte(*dat);
dat ;
}
}
void U2SendOneByte(unsigned char c)
{
S2BUF = c;
while(!(S2CON & S2TI));
S2CON &= ~S2TI;
}
void U2SendString(uchar *dat)
{
while(*(dat)!='\0')
{
U2SendOneByte(*dat);
dat ;
}
}
void main()
{ uchar temp = 0x01;
AUXR = AUXR|0x40; // T1, 1T Mode AUXR 第一次出现
InitUART1();
EA = 1;
SendOneByte(0xaa);
SendOneByte(0xbb);
SendOneByte(0xcc);
InitUART2();
SendOneByte(0xdd);
while(1)
{ // temp = ~temp;
// U2SendOneByte(temp);
if(finishflag)
{ LED1 = 1;
finishflag = 0;
U1SendString(ReceBuf);
LED1 = 0;
}
}
}
void UART1ISR(void) interrupt 4
{
if(RI)
{
RI = 0;
}
else
TI = 0;
}
void UART2ISR(void) interrupt 8
{ static bit flash=0;
static uchar i=0;
static uchar endcnt = 0;
uchar tempdat = 0;
if(S2CON & S2RI)
{
S2CON &= ~S2RI;
if(~finishflag)
{
flash=~flash;
// LED1 = flash;
tempdat = S2BUF;
if(tempdat=='$')
{
startflag = 1;
}
if(startflag)
{
ReceBuf[i] = tempdat;
i ;
if(i==6&&ReceBuf[3]!='R'&&ReceBuf[5]!='C') //判断是不是$GPRMC帧
{
startflag = 0;
i = 0;
}
else if(ReceBuf[i-1]=='*')
{
endcnt ;
if(endcnt==2)
{
revcnt = i;
endcnt = 0;
i = 0;
finishflag = 1;
startflag = 0;
}
}
else ;
}
}
else ;
}
else
S2CON &= ~S2TI;
}
|